Original Article
  • Evaluation of Fracture Behavior of Adhesive Layer in Fiber Metal Laminates using Cohesive Zone Models
  • Byoung-Eon Lee*, Eu-Tteum Park**, Dae-Cheol Ko***, Beom-Soo Kang**, Woo-Jin Song***†
  • *Aerospace Engineering Team 1, Koreanair R&D Center, **Department of Aerospace Engineering, Pusan National University, ***Graduate School of Convergence Science, Pusan National University, ***†Graduate School of Convergence Science, Pusan National University, Corresponding author (E-mail: woodysong@pusan.ac.kr)
  • 응집영역모델을 이용한 섬유금속적층판 접착층의 모드 I, II 파괴 거동 물성평가
  • 이병언* · 박으뜸** · 고대철*** · 강범수** · 송우진***†
Abstract
An understanding of the failure mechanisms of the adhesive layer is decisive in interpreting the performance of a particular adhesive joint because the delamination is one of the most common failure modes of the laminated composites such as the fiber metal laminates. The interface between different materials, which is the case between the metal and the composite layers in this study, can be loaded through a combination of fracture modes. All loads can be decomposed into peel stresses, perpendicular to the interface, and two in-plane shear stresses, leading to three basic fracture mode I, II and III. To determine the load causing the delamination growth, the energy release rate should be identified in corresponding criterion involving the critical energy release rate (GC) of the material. The critical energy release rate based on these three modes will be GIC, GIIC and GIIIC. In this study, to evaluate the fracture behaviors in the fracture mode I and II of the adhesive layer in fiber metal laminates, the double cantilever beam and the end-notched flexure tests were performed using the reference adhesive joints. Furthermore, it is confirmed that the experimental results of the adhesive fracture toughness can be applied by the comparison with the finite element analysis using cohesive zone model.

섬유금속적층판과 같은 하이브리드 소재는 여러 방향의 하중에 의한 접착층의 파괴로 인해 층간분리가 발생할 수 있다. 모든 하중은 수직 방향의 응력과 면내 두 방향의 전단 응력으로 분해할 수 있으며, 이러한 하중은 접착층의 모드 I, II, III 파괴를 일으킨다. 따라서 하중에 의한 층간분리 현상을 예측하기 위해, 접착층의 모드별 임계 에너지 해방률을 도출하는 것이 중요하다. 본 연구에서는 접착층의 모드 I 임계 에너지 해방률을 측정하기 위해 double cantilever beam 시험을 수행하였으며, 모드 II 임계 에너지 해방률을 측정하기 위해 end-notched flexure시험을 수행하였다. 또한, 실험으로부터 도출한 임계 에너지 해방률을 ABAQUS의 응집영역모델에 적용하여 유한요소해석을 수행하였으며, 실제 실험 결과와의 비교를 통해 층간분리 현상에 대한 수치해석 기법 적용의 유효성을 입증하였다.

Keywords: Fiber metal laminates, Double cantilever beam test, End-notched flexure test, Energy released rate, Cohesive zone model

Keywords: 섬유금속적층판, DCB 시험, ENF 시험, 에너지 해방률, 응집영역모델

This Article

  • 2016; 29(2): 45-52

    Published on Apr 30, 2016

Correspondence to

  • E-mail: