Original Article
  • A Study on the Application of Composites to Pipe Support Clamps for the Light-weight LNGC

  • Kyong-Min Bae*†, Yoon-Ji Yim**, Sung-Won Yoon*, Jong-Rok Ha*, Je-Hyoung Cho*

  • * Ocean ICT & Advanced Materials Technology Research Division, Research Institute of Medium & Small Shipbuilding
    ** Busan Textile Materials Research Center, Korea Dyeing and Finishing Technology Institute

  • LNGC 경량화를 위한 파이프 지지용 클램프의 복합소재 적용 연구

  • 배경민*† · 임윤지**· 윤성원*· 하종록*· 조제형*

  • This article is an open access article distributed under the terms of the Creative Commons Attribution Non-Commercial License (http://creativecommons.org/licenses/by-nc/4.0) which permits unrestricted non-commercial use, distribution, and reproduction in any medium, provided the original work is properly cited.

References
  • 1. Pi, J.W., Jeon, S.B., Lee, G.H., Jo, Y.D., Choi, J.H., and Kweon, J.H., “Joint Design and Strength Evaluation of Composite Air Spoiler for Ship”, Composites Research, Vol. 28, 2015, pp. 219-225.
  •  
  • 2. Kim, N.H., and Kim, J., “Technology Trend in Adhesive Materials for Heterogeneous Materials”, Journal of Adhesion and Interface, Vol. 19, 2018, pp. 173-176.
  •  
  • 3. Oh, D., Jung, S., and Jeong, S., “Effect of a Lightweight Hull Material and an Electric Propulsion System on Weight Reduction: Application to a 45ft CFRP Electric Yacht”, Journal of the Korean Society of Marine Environment and Safety, Vol. 24, 2018, pp. 818-824.
  •  
  • 4. Oh, D., Han, Z., Noh, J., and Jeong, S., “Laminate Weight Optimization of Composite Ship Structures based on Experimental Data”, Journal of the Society of Naval Architects of Korea, Vol. 57, 2020, pp. 104-113.
  •  
  • 5. Lee, H.S., Lim, B.C., Kim, M.T., Lee, B.S., and Park, S.H., “A Study on the Flow Analysis for KP505 Propeller Open Water Test”, Journal of the Korea Academia-Industrial Cooperation Society, Vol. 20, 2019, pp. 150-155.
  •  
  • 6. Choi, H.K., Nam, K.W., and Ahn, S.H., “Strength Characteristics of FRP Composite Materials for Ship Structure”, Journal of Ocean Engineering and Technology, Vol. 27, 2013, pp. 45-54.
  •  
  • 7. Choi, J., Kim, S.H., Bang, H.J., and Kim, K.J., “Development of Resin Film Infusion Carbon Composite Structure for UAV”, Composites Research, Vol. 32, 2019, pp. 45-49.
  •  
  • 8. Kong, C., Park, H., and Kang, K., “Structural Design and Analysis for Carbon/Epoxy Composite Wing of A Small Scale WIG Vehicle”, Journal of the Korean Society for Composite Materials, Vol. 19, 2006, pp. 12-19.
  •  
  • 9. Kim, S.H., Shin, H., and Bang, H.J., “Bend-Twist Coupling Behavior of 10 MW Composite Wind Blade,” Composites Research, Vol. 29, 2016, pp. 369-374.
  •  
  • 10. Wang, X., Wang, L., Ding, G., Yan, X., and Yue, S., “Experimental Study on Three-point Bending Performance of CFRP Shaft Embedded FBG Sensor”, IOP Conference Series: Materials Science and Engineering, Vol. 768, 2020, pp. 022063.
  •  
  • 11. Jia, X., Chen, G., Yu, Y., Li, G., Zhu, J., Luo, X., Duan, C., Yang, X., and Hui, D., “Effect of Geometric Factor, Winding Angle and Pre-crack Angle on Quasi-static Crushing Behavior of Filament Wound CFRP Cylinder”, Composites Part B Engineering, Vol. 45, 2013, pp. 1336-1343.
  •  
  • 12. Shen, W., Luo, B., Yan, R., Zeng, H., and Xu, L., “The Mechanical Behavior of Sandwich Composite Joints for Ship Structures”, Ocean Engineering, Vol. 144, 2017, pp. 78-89.
  •  
  • 13. Han, Z., Jeong, S., Noh, J., and Oh, D., “Comparative Study of Glass Fiber Content Measurement Methods for Inspecting Fabrication Quality of Composite Ship Structures”, Applied Sciences, Vol. 10, 2020, pp. 5130.
  •  
  • 14. Anyfantis, K.N., “Preliminary Design Assessment of an Alternative Repair Method for Corroded Shear Panels in Ship Hull Structures”, Ocean Engineering, Vol. 188, 2019, pp. 106323.
  •  
  • 15. Yang, Y., Fahmy, M. F., Guan, S., Pan, Z., Zhan, Y., and Zhao, T., “Properties and Applications of FRP Cable on Long-span Cable-supported Bridges: A Review”, Composites Part B: Engineering, Vol. 190, 2020, pp. 107934.
  •  
  • 16. Kharghani, N., and Guedes Soares, C., “Experimental and Numerical Study of Hybrid Steel-FRP Balcony Overhang of Ships under Shear and Bending”, Marine Structures, Vol. 60, 2018, pp. 15-33.
  •  
  • 17. Kharghani, N., and Guedes Soares, C., “Mechanical Properties Evaluation of the Components of a Failed Hybrid Steel-FRP Balcony Overhang in Ships”, Marine Structures, Vol. 68, 2019, pp. 102647.
  •  

This Article

Correspondence to

  • Kyong-Min Bae

  • Ocean ICT & Advanced Materials Technology Research Division, Research Institute of Medium & Small Shipbuilding

  • E-mail: kmbae@rims.re.kr