Original Article
  • Prediction of Failure Behavior for Carbon Fiber Reinforced Composite Bolted Joints using Progressive Failure Analysis

  • Donghyun Yoon*, Sangdeok Kim*, Jaehoon Kim*† , Youngdae Doh**

  • * Department of Mechanical Engineering, Chungnam National University
    ** HANKUK FIBER GROUP

  • 점진적 파손해석을 이용한 탄소섬유강화 복합재료 볼트 조인트의 파손거동 예측

  • 윤동현* · 김상덕* · 김재훈*† · 도영대**

  • This article is an open access article distributed under the terms of the Creative Commons Attribution Non-Commercial License (http://creativecommons.org/licenses/by-nc/4.0) which permits unrestricted non-commercial use, distribution, and reproduction in any medium, provided the original work is properly cited.

References
  • 1. Dutton, S., Kelly, D., and Baker, A., Composite Materials for Aircraft Structures, American Institute of Aeronautics and Astronautics, 2004.
  •  
  • 2. Hundley, J.M., Hahn, H.T., Yang, J.M., and Facciano, A.B., “Three-dimensional Progressive Failure Analysis of Bolted Titanium-graphite Fiber Metal Laminate Joints,” Journal of Composite Materials, Vol. 45, No. 7, 2011, pp. 751-769.
  •  
  • 3. Jeong, K.W., Choi, J.H., and Kweon, J.H., “A Study on the Strength of the Bolted Joint & Pin Joint with Hole Clearance,” Composites Research, Vol. 25, No. 6, 2012, pp. 186-190.
  •  
  • 4. Pi, J.W., Jeon, S.B., Lee, G.H., Jo, Y.D., Choi, J.H., and Kweon, J.H., “Joint Design and Strength Evaluation of Composite Air Spoiler for Ship,” Composites Research, Vol. 28, No. 4, 2015, pp. 219-225.
  •  
  • 5. ASTM D5961/D5961M-13, Standard Test Method for Bearing Response of Polymer Matrix Composite Laminates, ASTM Standard, 2013, pp. 1-31.
  •  
  • 6. Lapczyk, I., and Hurtado, J.A., “Progressive Damage Modeling in Fiber-reinforced Materials,” Composites Part A: Applied Science and Manufacturing, Vol. 38, No. 11, 2007, pp. 2333-2341.
  •  
  • 7. Riccio, A., Di Costanzo, C., Di Gennaro, P., Sellitto, A., and Raimondo, A., “Intra-laminar Progressive Failure Analysis of Composite Laminates with a Large Notch Damage,” Engineering Failure Analysis, Vol. 73, 2017, pp. 97-112.
  •  
  • 8. Matzenmiller, A., Lubliner, J., and Taylor, R.L., “A Constitutive Model for Anisotropic Damage in Fiber-composites,” Mechanics of Materials, Vol. 20, No. 2, 1995, pp. 125-152.
  •  
  • 9. Linde, P., and de Boer, H., “Modelling of Inter-rivet Buckling of Hybrid Composites,” Composite Structures, Vol. 73, No. 2, 2006, pp. 221-228.
  •  
  • 10. Hashin, Z., “Failure Criteria for Unidirectional Fiber Composites,” Journal of Applied Mechanics, Vol. 47, No. 2, 1980, pp. 329-334.
  •  
  • 11. Tikarrouchine, E., Chatzigeorgiou, G., Praud, F., Piotrowski, B., Chemisky, Y., and Meraghni, F., “Three-dimensional FE2 Method for the Simulation of Non-linear, Rate-dependent Response of Composite Structures,” Composite Structures, Vol. 193, 2018, pp. 165-179.
  •  
  • 12. Nikbakht, M., Toudeshky, H.H., and Mohammadi, B., “Experimental Validation of an Empirical Nonlinear Shear Failure Model for Laminated Composite Materials,” Journal of Composite Materials, Vol. 51, No. 16, 2017, pp. 2331-2345.
  •  
  • 13. Lee, C.S., and Lee, J.M., “Development of Progressive Failure Analysis Method for Composite Laminates based on Puck's Failure Criterion-Damage Mechanics Coupling Theories,” Journal of the Society of Naval Architects of Korea, Vol. 52, No. 1, 2015, pp. 52-60.
  •  
  • 14. Kodagali, K., Progressive Failure Analysis of Composite Materials using the Puck Failure Criteria, Doctoral Dissertation, University of South Carolina., USA, 2017.
  •  
  • 15. ASTM D3039/D3039M-14, Standard Test Method for Tensile Properties of Polymer Matrix Composite Materials, ASTM International, 2014, pp. 1-13.
  •  
  • 16. ASTM D3410/D3410M-16, Standard Test Method for Compressive Properties of Polymer Matrix Composite Materials with Unsupported Gage Section by Shear Loading, ASTM International, 2016, pp. 1-16.
  •  
  • 17. ASTM D5379/D5379M-12, Standard Test Method for Shear Properties of Composite Materials by the V-Notched Beam Method, ASTM International, 2012, pp. 1-14.
  •  
  • 18. ASTM Standard D5528-13, Standard Test Method for Mode I Interlaminar Fracture Toughness of Unidirectional Fiber-reinforced Polymer Matrix Composites, ASTM International, 2013, pp. 1-13.
  •  
  • 19. ASTM Standard D7905/D7905M-13, Standard Test Method for Determination of the Mode II Interlaminar Fracture Toughness of Unidirectional Fiber-reinforced Polymer Matrix Composites, ASTM International, 2013, pp. 1-18.
  •  
  • 20. Pinho, S.T., Robinson, P., and Iannucci, L., “Fracture Toughness of the Tensile and Compressive Fibre Failure Modes in Laminated Composites,” Composites Science and Technology, Vol. 66, No. 13, 2006, pp. 2069-2079.
  •  
  • 21. Laffan, M.J., Pinho, S.T., Robinson, P., and Iannucci, L., “Measurement of the in situ Ply Fracture Toughness Associated with Mode I Fibre Tensile Failure in FRP. Part I: Data Reduction,” Composites Science and Technology, Vol. 70, No. 4, 2010, pp. 606-613.
  •  
  • 22. Laffan, M.J., Pinho, S.T., Robinson, P., and Iannucci, L., “Measurement of the in situ Ply Fracture Toughness Associated with Mode I Fibre Tensile Failure in FRP.Part II: Size and Lay-up Effects”, Composites Science and Technology, Vol. 70, No. 4, 2010, pp. 614-621.
  •  
  • 23. Cann, M.T., Adams, D.O., and Schneider, C.L., “Characterization of Fiber Volume Fraction Gradients in Composite Laminates,” Journal of Composite Materials, Vol. 42, No. 5, 2008, pp. 447-466.
  •  
  • 24. Kang, M.S., Jeon, M.H., Kim, I.G., Kim, M.G., Go, E.S., and Lee, S.W., “The Effect of the Fiber Volume Fraction Non-uniformity and Resin Rich Layer on the Rib Stiffness Behavior of Composite Lattice Structures,” Composites Research, Vol. 31, No. 4, 2018, pp. 161-170.
  •  
  • 25. Shigley, J.E., Shigley’s Mechanical Engineering Design, Vol. 8., McGraw-Hill, New York, NY, USA, 2008.
  •  
  • 26. Herrington, P.D., and Sabbaghian, M., “Factors Affecting the Friction Coefficients between Metallic Washers and Composite Surfaces,” Composites, Vol. 22, No. 6, 1991, pp. 418-424.
  •  

This Article

Correspondence to

  • Jaehoon Kim

  • Department of Mechanical Engineering, Chungnam National University

  • E-mail: kimjhoon@cnu.ac.kr