Original Article
  • 단섬유 복합소재 사출 성형품의 기계적 거동 예측을 위한 2D Shell 기반 사출 성형-구조 연계 해석

  • JeongMin Kim*, GeungHyeon Lee*, YeongHun Seol*, JeongUk Choe*, Yunki Gwak*, Jang-Woo Han*†

  • * Department of Mechanical Engineering, Kumoh National Institute of Technology

  • 2D Shell-Based Injection Molding-Structural Coupled Analysis for Predicting the Mechanical Behavior of Injection-Molded Short-Fiber Reinforced Composites

  • 김정민* · 이긍현* · 설영훈* · 최정욱* · 곽윤기* · 한장우*†

  • This article is an open access article distributed under the terms of the Creative Commons Attribution Non-Commercial License (http://creativecommons.org/licenses/by-nc/4.0) which permits unrestricted non-commercial use, distribution, and reproduction in any medium, provided the original work is properly cited.

References
  • 1. Papathanasiou, T.D., and Guell, D.C., “Flow-Induced Alignment in Composite Materials,” Woodhead Publishing, Cambridge, UK, 1997, pp. 112-120.
  •  
  • 2. Lee, M.H., and Lee, K.J., “Numerical Prediction of Short Fiber Orientation in Injection Molding Process,” The Korea Journal of Rheology, Vol. 4, No. 2, 1992, pp. 138-147.
  •  
  • 3. Park, S.S., Yoon, S.U., Jo, S.H., and Kim, E.G., “A Study on Fiber Content Distribution of Injection Molded Fiber-Reinforced Polymeric Composites,” Composites Research, Vol. 10, No. 1, 1997, pp. 83-89.
  •  
  • 4. Jeffery, G.B., “The Motion of Ellipsoidal Particles Immersed in a Viscous Fluid,” Proceedings of the Royal Society of London, Series A, Vol. 102, No. 715, 1922, pp. 161-179.
  •  
  • 5. Folgar, F., and Tucker, C.L., “Orientation Behavior of Fibers in Concentrated Suspensions,” Journal of Reinforced Plastics and Composites, Vol. 3, No. 2, 1984, pp. 98-119.
  •  
  • 6. Advani, S.G., and Tucker III, C.L., “The Use of Tensor to Describe and Predict Fiber Orientation in Short Fiber Composites,” Journal of Rheology, Vol. 31, No. 8, 1987, pp. 751-784.
  •  
  • 7. Bay, R.S., and Tucker III, C.L., “Fiber Orientation in Simple Injection Moldings. Part I: Theory and Numerical Results,” Polymer Composites, Vol. 13, No. 4, 1992, pp. 317-331.
  •  
  • 8. Bay, R.S., and Tucker III, C.L., “Fiber Orientation in Simple Injection Moldings. Part II: Experimental Results,” Polymer Composites, Vol. 13, No. 4, 1992, pp. 332-341.
  •  
  • 9. Tseng, H.C., Chang, R.Y., and Hsu, C.H., “The use of shear-rate-dependent parameters to improve fiber orientation predictions for injection molded fiber composites,” Composites Part A, Vol. 104, 2018, pp. 81-88.
  •  
  • 10. Gupta, M., and Wang, K.K., “Fiber Orientation and Mechanical Properties of Short-Fiber-Reinforced Injection-Molded Composites: Simulated and Experimental Results,” Polymer Composites, Vol. 14, No. 5, 1993, pp. 367-382.
  •  
  • 11. Lee, S.W., and Youn, J.R., “Effects of Compressibility of Polymer Melt on Fiber Orientation and Mechanical Properties of Short Fiber Reinforced Composites,” Composites Research, Vol. 11, No. 4, 1998, pp. 43-54.
  •  
  • 12. Kang, T.Y., An, H.S., Chun, H.J., and Park, J.C., “Fatigue Behavior of Composites with Different Fiber Orientation,” Composites Research, Vol. 34, No. 2, 2021, pp. 77-81.
  •  
  • 13. Mortazavian, S., and Fatemi, A., “Effects of Fiber Orientation and Anisotropy on Tensile Strength and Elastic Modulus of Short Fiber Reinforced Polymer Composites,” Composites Part B: Engineering, Vol. 72, 2015, pp. 116-129.
  •  
  • 14. Bernasconi, A., Davoli, P., Basile, A., and Filippis, A., “Effect of Fiber Orientation on the Fatigue Behavior of a Short Glass Fiber Reinforced Polyamide-6,” International Journal of Fatigue, Vol. 29, No. 2, 2007, pp. 199-208.
  •  
  • 15. Park, Y.B., Yang, H.J., Kweon, J.H., Choi, J.H., and Cho, H.I., “Failure of Composite Sandwich Joints under Pull-out Loading,” Composites Research, Vol. 24, No. 1, 2011, pp. 17-23.
  •  
  • 16. Kim, Y.M., and Kim, Y.H., “Coupled Analysis with Digimat for Realizing the Mechanical Behavior of Glass Fiber Reinforced Plastics,” Journal of Computational Structural Engineering Institute of Korea, Vol. 32, No. 6, 2019, pp. 349-357.
  •  
  • 17. Lee, G.H., Kim, H.W., Kim, D.H., Chae, B.M., Kim, J.M., Seol, Y.H., Jang, D.Y., Kim, Y.I., Lee, H.Y., Moon, K.H., Ko, K.U., Lee, Y.M., and Han, J.W., “Injection Molding-Structural Coupled Analysis for High-strength/Lightweight Design of EV Battery Pack Case made by Short-fiber Reinforced Composites,” Composites Research, Vol. 38, No. 4, 2025, pp. 448-457.
  •  
  • 18. Kim, Y.M., and Kim, Y.H., “A Study on the Fatigue Analysis of Glass Fiber Reinforced Plastics with Linear and Nonlinear Multi-Scale Material Modeling,” Journal of Computational Structural Engineering Institute of Korea, Vol. 33, No. 2, 2020, pp. 81-93.
  •  

This Article

Correspondence to

  • Jang-Woo Han

  • * Department of Mechanical Engineering, Kumoh National Institute of Technology

  • E-mail: uddan@kumoh.ac.kr