Original Article
  • Failure Characteristics of Scarf Patch-repaired Composite Single-lap Joints
  • Choong-Hyun Kim*, Jae-Seung Yoo*, Chang-Seok Byeon*, Hyun-Woo Ju*, Min-Young Park**, Jin-Ho Choi***, Jin-Hwe Kweon***†
  • *School of Mechanical and Aerospace Engineering, Gyeongsang National University **Agency for Defense Development ***†School of Mechanical, Aerospace and Information Engineering, Research Center for Aircraft Parts Technology, Gyeongsang National University
  • 스카프 패치로 수리한 복합재 단일겹침 체결부의 파손 특성 연구
  • 김충현* · 유재승* · 변창석* · 주현우* · 박민영** · 최진호*** · 권진회***†
Abstract
The failure strength of composite single-lap joint repaired using scarf patch was investigated by test and finite element method. A total of 45 specimens were tested changing scarf ratio, stacking pattern, and defect size to study the failure strength and mode. Except for one case, all repaired specimens showed the equal or higher strength than the sound specimens and the effect of considered repair parameters was not remarkable. It was found through the failure mode inspection that the surface treatment for bonding was not enough in the case which failed at the lower load than the sound specimen. Three-dimensional finite element analysis was conducted to verify the test results. It was confirmed that the considered repair parameters do not significantly affect the stress distribution of the specimens. It was also observed that the applied tensile load is relieved passing through the overlapped region thickness of which is almost double. From this study, it is concluded that if the bonding procedure for adherends and patch including surface treatment for fabric layer is thoroughly followed, the strength of repaired single-lap joint can be restored up to the strength of sound one.

본 연구에서는 스카프 패치로 수리한 복합재 단일겹침 체결부의 파손강도를 시험과 해석으로 연구하였 다. 스카프 비, 모재의 적층패턴, 결함크기를 달리 하며 총 45개의 시편에 대한 시험을 수행하여 파손강도와 파손 모드를 분석하였다. 다양한 형상의 시편에 대한 시험 결과, 한 경우를 제외하고는 수리 후의 체결부가 결함이 없 는 체결부 강도 이상의 강도를 회복하며, 체결부 인자에 따른 특별한 차이는 나타나지 않는 것을 확인하였다. 파 손강도가 낮게 나타난 한 경우에 대한 파손면 분석결과 모재의 표면층인 평직층의 표면처리가 충분치 않은 것이 원인인 것으로 판단되었다. 시험 결과의 분석을 위해 3차원 유한요소해석을 수행하였는데, 유한요소해석에서도 고려한 체결부 인자가 상하부 모재와 패치, 접착층에서의 응력에 큰 영향을 미치지 않는 것을 확인하였다. 이는 단일겹침 체결부의 경우 외부 인장하중이 겹침영역을 통과하면서 상하부 모재로 분산되기 때문인 것으로 판단된 다. 시험과 해석 결과 모재 중앙에 결함이 존재하는 단일겹침 체결부의 경우 절차에 따라 패치 접착이 이루어지 고, 모재의 표면처리가 충분히 이루어진다면 수리를 통해 손상 전 강도를 회복할 수 있는 것으로 판단된다.

Keywords: Composite material, Single-lap joint, Repair, Scarf patch, Strength recovery rate

Keywords: 복합재료, 단일겹침 체결부, 수리, 스카프 패치, 강도 회복률

This Article

  • 2016; 29(3): 117-124

    Published on Jun 30, 2016