Original Article
  • Design and Verification of a Novel Composite Sandwich Joint Structure
  • School of Mechanical and Aerospace and Engineering, Gyeongsang National University School of Mechanical and Aerospace and Engineering, Gyeongsang National University, Corresponding author (E-mail: jhkweon@gnu.ac.kr) Agency for Defense Development Hankuk Fiber Co., Ltd. Defence and Aerospace Division
  • 새로운 개념의 복합재 샌드위치 체결부 구조의 설계와 검증
  • 곽병수 · 주현우 · 김홍일 · 동승진 · 권진회
Abstract
Sandwich panels with three different joint configurations were tested to design a novel sandwich joint structure that can effectively support both the tensile and compressive loads. The sandwich core was mainly aluminum flex honeycomb but the PMI foam core was limitedly applied to the ramp area which is transition part from sandwich to solid laminate. The face of sandwich panel was made of carbon fiber composite. For configuration 1, the composite flange and the sandwich panel were cocured. For configurations 2 and 3, an aluminum flange was fastened to the solid laminate by HI-LOK pins and adhesive. The average compressive failure loads of configurations 1, 2, and 3 were 295, 226, and 291 kN, respectively, and the average tensile failure loads were 47.3 (delamination), 83.7 (bolt failure), and 291 (fixture damage) kN, respectively. Considering the compressive failure loads only, both the configurations 1 and 3 showed good performance. However, the configuration 1 showed delamination in the corner of the composite flange under tension at early stage of loading. Therefore, it was confirmed that the structure that can effectively support tension and compressive loads at the same time is the configuration 3 which used a mechanically fastened aluminum flange so that there is no risk of delamination at the corner.

인장과 압축하중 모두를 효과적으로 지지할 수 있는 새로운 샌드위치 체결부 구조의 설계를 위해, 체결 부 형상이 다른 3가지 샌드위치 판넬에 대한 인장 및 압축 시험을 수행하였다. 샌드위치 판넬의 코어는 주로 알 루미늄 플렉스 허니콤이지만, 타 구조물과의 체결을 위해 두께가 얇아지면서 단순 적층판으로 변하는 램프 영역 에서는 PMI 폼 코어를 사용하였고, 면재에는 탄소섬유 복합재를 사용하였다. 형상 1에서는 복합재 플랜지와 샌 드위치 구조가 일체형으로 연결된다. 형상 2와 3에서는 별도로 제작된 알루미늄 플랜지가 복합재 적층판에 하이 록핀과 접착제로 체결된다. 시험 결과 형상 1, 2, 3의 평균 압축파손하중은 각각 295 kN, 226 kN, 291 kN으로 나타 났고, 평균 인장파손하중은 각각 47.3(층간분리), 83.7 kN(볼트파손), 291 kN(치구손상)으로 나타났다. 압축 파손하 중만을 고려할 경우 플랜지와 샌드위치 판넬을 복합재 일체형으로 제작한 형상 1과 3이 우수한 특성을 보였다. 그 러나 형상 1의 경우 인장하중을 받을 때 낮은 하중에서 플랜지 모서리 부분에서 층간분리가 발생하였다. 따라서 인장과 압축하중을 동시에 효과적으로 지지할 수 있는 구조는 모서리에서 층간분리의 위험이 없게 별도의 알루 미늄 플랜지를 사용하여 볼트로 체결한 형상 3임을 확인하였다.

Keywords: Composite material, Sandwich, Joint, Failure

Keywords: 복합재료, 샌드위치, 체결부, 파손

This Article

  • 2017; 30(6): 384-392

    Published on Dec 31, 2017